How a telecommunications upgrade disrupted US air travel nationwide

A router malfunction during planned maintenance reportedly disrupted aircraft communications and radar feeds, forcing the FAA to ground departing flights for more than four hours.

A planned replacement of copper wires with fibre-optic links triggered a network disruption that grounded flights across the United States. Photo: Pexels
T
7 min read  |  Published: 16 Nov 2026

Sydney: On Friday, all flights across the United States were grounded for more than four hours following what appeared to be a telecommunications issue.

The Federal Aviation Administration (FAA) issued an alert citing “extraordinary circumstances” and directed all departing flights to remain grounded until further notice. According to media reports, about 3,500 flights were in the air when the alert was issued, and all landed safely.

With thousands of flights delayed or cancelled, millions of passengers faced disruption at airports. The situation gradually began to return to normal over the weekend.

The ground stop was attributed to an update to air traffic control equipment during planned maintenance. So, what exactly happened?

What caused the disruption?

US Transportation Secretary Sean Duffy attributed the disruption to maintenance work carried out by government contractor L3Harris at a remote FAA facility.

The work involved replacing copper telecommunications wires with fibre-optic links and changing how the system transmits data, moving from an older method known as time-division multiplexing (TDM) to the more recent internet protocol (IP).

During the maintenance, a router, a networking device, reportedly generated more than 1,000 connection requests every four to five seconds. This affected other routers on the network, disrupting aircraft communications and some radar data feeds.

Duffy described the upgrade as a transition from analogue to digital technology. However, this conflates two different aspects of telecommunications.

Copper and fibre refer to the physical medium that carries signals, while TDM and IP describe how information is transmitted and organised. Copper cables can carry digital data, and TDM is widely used in digital telecommunications. Fibre-optic systems also carry digital data, using light rather than electrical signals.

Therefore, replacing copper with fibre does not necessarily mean a change from analogue to digital technology.

The more significant change involved the method used to transmit information. With TDM, the system sends information through a single channel in fixed time slots, much like traffic crossing a single-lane bridge at set intervals.

An IP network, by contrast, carries information in packets that can travel along different routes. This improves flexibility and increases the amount of data the network can handle.

However, it also changes how equipment interacts and how faults can affect the network. If a malfunction is not isolated in time, a faulty router can affect other equipment connected to the same network. On fibre-optic links, excessive connection requests can also be transmitted rapidly across the network.

Why would a network disruption ground planes?

Air traffic controllers rely on surveillance systems and radio communications to manage aircraft movements and keep planes safely separated.

Radar and satellite-based surveillance systems provide information on aircraft positions, while communications allow controllers to issue instructions and coordinate movements between control centres.

These functions depend on telecommunications networks connecting facilities across the country. Aircraft can navigate independently during a network failure, but controllers cannot safely manage the usual volume of flights if communications are unreliable.

The precise reason the router generated so many requests remains under investigation. Incorrect installation, configuration errors and defective equipment are among the possible explanations. The findings of the investigation will be needed to establish what went wrong.

A nationwide ground stop following a technical failure is not unprecedented. In January 2023, a malfunction in the FAA's Notice to Air Missions system, which provides pilots with operational information, also led to the suspension of departures across the United States.

Although the two incidents involved different systems, both demonstrate how a fault in a national aviation network that relies on interconnected services can have widespread consequences.

Was it related to Microsoft or AI?

The incident prompted speculation about a possible connection with the global Microsoft outage that occurred just a day earlier.

Another suggestion was that the fault might be linked to the FAA's recently announced expansion of SMART, an artificial intelligence-assisted traffic management system.

Both Microsoft and Air Space Intelligence, the company responsible for SMART, denied involvement. Officials also said the network maintenance was entirely separate from the air traffic control modernisation programme.

What can be done to prevent a repeat?

In September 2026, a US government report classified 51 of the FAA's 138 air traffic control systems as unsustainable and another 54 as potentially unsustainable. The FAA is working to replace ageing communications, radar and control equipment.

However, modernisation also introduces risks. New technology must be integrated with existing infrastructure without disrupting ongoing operations.

Preventing similar ground stops will require more than replacing cables or purchasing new equipment. Segmenting the network could limit how far a fault spreads. Proper configuration and safeguards could also prevent communications systems from becoming overloaded if a similar router malfunction occurs.

The ground stop was a safety measure taken when communications became unreliable. But a resilient aviation system must do more than respond safely to equipment failures. It must also prevent localised technical problems from disrupting operations across the country.

To advertise here,contact us